3-Axis Slider Parts
Quantity
Nema 17 42 x 42 x 40mm Stepper Motor: 1
Nema 17 42 x 42 x 23mm Stepper Motor: 2
TMC2208 Stepper Motor Driver: 3
Arduino Nano: 1
JDY-31 Bluetooth Module (Alternatively HC-05, HC-06 or JDY-30): 1
A3144 Hall Effect Sensor: 3
6.4mm diameter x 1.7mm Neodymium Magnets: 2
3.2mm diameter x 1.7mm Neodymium Magnets: 4
2N3904 NPN Transistor: 1
330Ω Resistor: 1
470Ω Resistor: 1
15kΩ Resistor: 1
22kΩ Resistor: 1
33kΩ Resistor: 2
100μF Electrolytic Capacitor: 3
2 Pin Plug-In Screw Terminal Block Connector 5.08mm Pitch (for power): 1
6 Pin Female Header Connector 2.54mm (for Bluetooth module): 1
15 Pin Female Header Connector 2.54mm (for Arduino Nano): 2
15 Pin Male Header Connector 2.54mm (for Arduino Nano): 2
8 Pin Female Header Connector 2.54mm (for Stepper drivers): 6
8 Pin Male Header Connector 2.54mm (for Stepper drivers): 6
XH2.54 4 Pin Terminal Socket Header (for Stepper motors): 3
XH2.54 4 Pin Terminal Socket Plug (for Stepper motors): 3
XH2.54 3 Pin Terminal Socket Header (for Hall Effect): 3
XH2.54 3 Pin Terminal Socket Plug (for Hall Effect): 3
XH2.54 2 Pin Terminal Socket Header (for camera shutter trigger): 1
XH2.54 2 Pin Terminal Socket Plug (for camera shutter trigger): 1
2.5mm 3 pole Jack Male (for camera trigger): 1
11.1V 3S LiPo Battery or 12V DC Power Source and connector to screw terminal: 1
Pan Tilt Mount PCB: 1
Solder Wire
Cyanoacrylate or Hot Glue (for magnets and Hall Effect sensor)
Wire (for Stepper motors, Hall sensors, Bluetooth module)
M3 Hexagonal Nyloc Nut: 16
M3 Square Nut: 10
M3 Button Head Hex Bolt 40mm: 4
M3 Button Head Hex Bolt 20mm: 3
M3 Button Head Hex Bolt 16mm: 10
M3 Button Head Hex Bolt 12mm: 14
M3 Button Head Hex Bolt 8mm: 5
M3 Button Head Hex Bolt 6mm: 5
M3 Button Head Hex Bolt 3.5mm: 1
Camera Mounting Bolt: 1
M3 T-Nut for Aluminium Extrusion Profile: 4
Screw 2mm Outer Thread Diameter, 6mm Long: 3
2GT Timing Belt: 1
2GT Timing Pulley 36 Teeth: 1
V-Slot 2040 Aluminium Extrusion: 1
F623ZZ Flange Bushing Ball Bearings 3 x 10 x 4mm: 6
V-Slot Pulley Wheels with Bearings (24 x 16 x 10.2mm): 4
3D Printed Parts:127 x 146.05 x 12.7mm INA CSXU050-2RS Bearing
Or 3D printable bearing parts 1-3 and 28 x 6mm balls (BB pellets): 1
21 Tooth Herringbone Gear: 1
64 Tooth Herringbone Gear: 1
17 Tooth Herringbone Gear: 1
144 Tooth Herringbone Gear Base Mount: 1
Tilt U-Mount: 1
Idle Side Bearing Mount: 1
Gear Side Bearing Mount: 1
Idle Side Support: 1
Gear Side Support: 1
Pan Mount: 1
Pan Mount Bearing Clamp: 1
Base Mount Bearing Clip Ring: 1
2040 hall clamp: 1
2040 slider carriage top: 1
2040 slider carriage bottom: 1
2040 belt clamp side 1: 1
2040 belt clamp side 2: 1
2040 support leg (Optional)
Belt clamp lever: 2
3mm to 5mm wheel bearing spacer centred: 4
5mm to 8mm shaft spacer (for timing pulley if it has a 8mm bore): 1
